﻿GET_GEVOMechL2_02_01_01_116 - ANIMATION Screen
1
00:00:00,000 --> 00:00:03,083
Lubricating Oil Filter Housing Removal

2
00:00:03,083 --> 00:00:06,792
1. Drain the oil from the lubricating oil filter housing.

3
00:00:06,792 --> 00:00:12,500
2. Remove the applicable locomotive handrail section to allow for oil filter housing removal.

4
00:00:12,500 --> 00:00:16,250
3. Disconnect the oil filter housing from the oil cooler.

5
00:00:16,250 --> 00:00:22,292
4. Remove the ten mounting bolts that secure the oil filter housing to the floor of the radiator cab.

6
00:00:22,292 --> 00:00:27,250
5. Attach lifting slings or cables to the holes on the lubricating oil filter.

7
00:00:27,250 --> 00:00:34,583
6. With the appropriate lifting device, gently slide and then lift the oil filter housing to remove it from the radiator cab.

8
00:00:34,583 --> 00:00:37,833
Lubricating Oil Filter Housing Installation

9
00:00:37,833 --> 00:00:42,542
1. Attach lifting slings or cables to the holes on the lubricating oil filter.

10
00:00:42,542 --> 00:00:50,125
2. Lift the lubricating oil filter housing and manually rotate the filter housing to pass through the support bar of the radiator cab.

11
00:00:50,125 --> 00:00:57,250
3. Place the oil filter housing on the radiator cab floor and gently slide it through the radiator cab to the mounting location.

12
00:00:57,250 --> 00:01:13,542
4. Install the ten mounting bolts that secure the filter housing to the floor of the radiator cab, then torque the bolts to 105-115 lb.-ft. (142-156 Nm) in a crisscross pattern.

13
00:01:13,542 --> 00:01:17,667
5. Connect the oil cooler to the oil filter housing as follows:

14
00:01:17,667 --> 00:01:29,000
a. Remove the plugs and unblock all flange and pipe openings, then reconnect the oil filter housing drain back valve drain flange and drain piping assembly and install the previously removed hardware.

15
00:01:29,000 --> 00:01:38,875
b. Remove the plugs and unblock all flange and pipe openings, then reconnect the pipe sections on the back of the oil filter housing and install the previously removed hardware.

16
00:01:38,875 --> 00:01:47,792
c. Remove the blanking plate and plugs and then reconnect the piping connecting the oil cooler to the oil filter housing and install the previously removed hardware.

17
00:01:47,792 --> 00:01:51,250
6. Install the previously removed handrail section.

18
00:01:51,250 --> 00:01:54,833
7. Fill the lubricating oil system, if required.

19
00:01:54,833 --> 00:02:08,292
8. Once the oil filter housing is installed, close the BS and then close the LCCB, FPB, and BCCB on the EC panel, remove the warning tag from the EC switch, and start the engine.

20
00:02:08,292 --> 00:02:13,292
9. With the engine at IDLE, check and fill the crankcase lubricating oil level.

21
00:02:13,292 --> 00:02:16,458
Lubricating Oil Filter Element Replacement

22
00:02:16,458 --> 00:02:20,125
1. Drain the oil from the lubricating oil filter housing.

23
00:02:20,125 --> 00:02:25,083
2. Loosen the 10 nuts securing the filter housing door and crack the door seal.

24
00:02:25,083 --> 00:02:30,000
3. Further loosen the nuts securing the filter housing door and fully open the door.

25
00:02:30,000 --> 00:02:36,542
4. Remove the 10 used filter elements and inspect the outer surfaces of the used elements for metal particles.

26
00:02:36,542 --> 00:02:38,667
5. Discard the used elements.

27
00:02:38,667 --> 00:02:44,917
6. Wipe clean the inside of the filter housing to prevent the old oil in the housing from contaminating the new oil.

28
00:02:44,917 --> 00:02:47,792
7. Install new approved filter elements.

29
00:02:47,792 --> 00:02:51,667
8. Ensure all filter elements are properly seated and clamped.

30
00:02:51,667 --> 00:02:55,583
9. Inspect the filter housing door O-ring and replace if needed.

31
00:02:55,583 --> 00:03:01,875
10. Close the filter housing door and torque the clamping nuts in a crisscross pattern to the torque indicated on the label.

32
00:03:01,875 --> 00:03:06,583
11. Close the lubricating oil filter housing vent and drain back valves.

33
00:03:06,583 --> 00:03:11,208
12. Restore the locomotive and check and fill oil in the engine crankcase.